HYDRATECH HYDRALINE 4135
HydraTech HydraLine 4135
Advantages
Physical Properties
Application Recommendations
Substrate Preparation
Performance Data
Installation Procedure
Note
Ordering Information
HYDRATECH HYDRALINE 4135
- The HydraLine 4135 is a unique, high performance acid resistant coating.
- The 4135 provides excellent adhesion to a variety of substrates while allowing a sag free application at high film builds.
- HydraLine 4135 can be filled with chopped fibers to create a chemical resistant filler / putty or be filled with Portland cement to form a chemical resistant mortar / grout.
- The HydraLine 4135 can be utilized in combination with a variety of woven fabrics to give a chemical resistant structural repair.
ADVANTAGES
- Rapid development of physical properties with ambient cure. No post cure required.
- Excellent Chemical Resistance
- Excellent Adhesion
- 100% Solvent-Free, Zero V.O.C.
- Low temperature cure down to 40ºF (4ºC).
- Full contract support services, if required
The HydraTech HydraLine 4135 is a performance driven product that provides a chemical and corrosion resistant repair for primary and secondary containment applications. The 4135 is backed by our engineering staff that services each application with assessment and technical support.
PROPERTIES
| Color | Steel Green |
| Working Life –68ºF (20ºC) | 15 minutes |
| Dry Times – 68ºF (20ºC) | 4 Hours |
| % Vol Solids (ASTM 2369) | 100 |
| Shore D Hardness (ASTM D2240) | 80 |
| Mix Ratio | Pre-measured 1:1/container |
| Flash Point | > 200ºF (93ºC) |
| Storage Life - Twelve months when stored in original sealed containers, between 50-77ºF (10-25ºC) | |
| Adhesion to Cold Rolled Steel (psi) (ASTM D4541) | >2,000 |
| Adhesion to Hot Rolled Steel (psi) (ASTM D4541) | >2,000 |
| Adhesion to Cast Iron (psi) (ASTM D4541) | >2,000 |
| Adhesion to 304 Stainless (psi) (ASTM D4541) | >2,000 |
| Adhesion to 316 Stainless (psi) (ASTM D4541) | >2,000 |
| Adhesion to Concrete (ASTM D4541) | Concrete Failure |
APPLICATION RECOMMENDATIONS
| Minimum Application Temperature | 40ºF (4.4ºC) |
| Maximum Relative Humidity | 85% |
| Substrate Temperature | 5ºF (3ºC) above dew point |
| Thinning | Do not thin |
| Cleaning Fluid | Hunting Universal Equipment Cleaner To aid application at low temperatures, both components should be warmed to 60-68ºF (15.5-20ºC) prior to mixing. |
SUBSTRATE PREPARATION
Substrate preparation dictates the adhesion performance of any coatings system. A properly prepped surface will ensure maximum life and performance of the system.
| Concrete: | NACE No.6*/SSPC-SP13* |
| Steel: | NACE No.2* / SSPC-SP 10* NACE No.3 / SSPC-SP 6 NACE No.5 / SSPC-SP 12 |
| *indicates recommended method | |
PERFORMANCE DATA
CHEMICAL RESISTANCE ASTM D543 (31 day immersion) |
|
| Water | No Effect |
| Sodium Hydroxide 5% | No Effect |
| Ammonium Hydroxide 5% | No Effect |
| Sodium Hypochlorite (bleach) | No Effect |
| Ferric Chloride 1% | No Effect |
| Sulfuric Acid 98% | Discoloration |
| Nitric Acid 1% | No Effect |
| Detergent Solution | No Effect |
| Gasoline | No Effect |
| Toluene | No Effect |
| Phosphoric Acid 50% | No Effect |
| Hydrochloric Acid 36% | No Effect |
| Testing reflects results after seven day cure | |
ADHESION ASTM D4541 |
|
| Cold Rolled Steel | >2,000 psi |
| Hot Rolled Steel | >2,000 psi |
| Cast Iron | >2,000 psi |
| 304 Stainless Steel | >2,000 psi |
| 316 Stainless Steel | >2,000 psi |
| Concrete | Concrete Failure |
| Testing reflects results after seven day cure | |
| INHALATION | Wear suitable respiratory cartridge mask in enclosed spaces. Work in well ventilated areas. |
| EYES | Wear suitable goggles. |
| SKIN | Wear protective clothing and gloves made of impervious material. |
| STORAGE | Store away from direct sunlight and sources of heat. Store at 40º to 90ºF (4º to 32ºC). Avoid Freezing. |
INSTALLATION PROCEDURE
- Prep substrate
- Mechanically mix together both 4135 components until uniform in color.
- Apply 4135 to prepared substrate via brush or spreader.
- Allow 4135 to cure a minimum of 24Hr before return to service, permit seven day cure for immersion applications in contact with aggressive reagents.
NOTE
The 4135 System is not intended for applications with exposure to strong acids, organic acids, strong solvents (MEK, Acetone, Alcohol) at elevated temperatures. Consult technical staff regarding applications where exposure to organic acids or strong solvents may exist. To be applied by certified personnel only. See MSDS for additional safety information. System will discolor when exposed to sunlight.
| Kit Size | Coverage | |
| 4135 | Pt |
4.5 sqft 9 sqft 23.5 sqft |
| (Primer coverage based on 32mil film build. | ||
ORDER INFORMATION
Part No. for standard kits consist of: Product Code - Component - Container Code
Pint Kit |
Quart Kit |
Half Gallon Kit |
4135A63 |
4135A71 |
4135A11 |
4135B63 |
4135B71 |
4135B75 |
*** NOTE: Custom kit quantities can be packaged for special application. *** |
||